Fastener sealing
Fasteners are covered with sealant so washers are no longer the only barrier.
Metal Roofing
Metal Roof Coating Tenafly, NJ
A Tenafly roofer can tell you whether a metal roof is a good coating candidate and apply the full system: cleaning, rust treatment, primer, seam sealing and topcoat, when the metal underneath is still solid. Call (551) 355-3330 to reach a local roofer.
A coating renews a metal roof whose finish has worn away but whose panels are still sound. By the time a metal roof is a coating candidate, the paint is usually chalky, rust has started at screw heads and seams and a few fasteners leak. A coating is not a structural repair, so damaged panels and framing are handled first.
Most metal roof coatings are acrylic or silicone. Acrylic coatings stretch with the metal, reflect sunlight and can be recoated with the same material later. Silicone stands up to ponding and sun, which is why it is popular on low slope metal.
Most coating failures come from skipped prep, not bad material. The roof has to be cleaned of chalk, dirt and oil, rust has to be treated, and fasteners and seams have to be sealed before the base coat goes on. The work needs a stretch of dry, mild weather.
If the problem goes deeper than it first looked, a Tenafly roofer may also recommend metal roof repair or roof coating.
Need metal roof coating in Tenafly? Call (551) 355-3330 and describe the problem to a roofer who works in Tenafly.
Call nowThe process
What happens during a metal roof coating
The steps below are typical for a metal coating system.
Assess the candidate
The inspection rules out rust holes, loose panels and structural problems. A small adhesion test patch is often applied to confirm the coating will bond.
Clean the surface
The roof is washed to remove chalk, dirt, oil and loose paint, often with a cleaner made for coating prep. The roof is allowed to dry completely before the next step.
Rust prep
Rusted areas are wire brushed and primed with a rust-inhibiting primer. Galvanized or heavily rusted roofs may get a full primer coat.
Reinforce seams
Worn screws are replaced or tightened, then each fastener head is covered with sealant, and seams and laps are reinforced with polyester fabric embedded in coating. Penetrations and pipe boots get the same treatment.
Apply the coating
The base and top coats are applied by roller or sprayer at the specified thickness, measured as they go. Correct thickness is what gives a coating its life span.
What is included
Parts of a coating system
Reflective coating
A flexible coating covers the whole roof for a seamless surface.
Rust treatment
Bare metal is primed for long-lasting protection.
Roof cleaning
The roof is washed and degreased before priming.
Seam reinforcement
End and side laps are sealed with embedded polyester fabric.
Related service
Metal Roof Restoration Tenafly, NJ
A metal roof restoration combines repairs and a coating system to give a tired roof another long run. Before coating, rusted panels are replaced, screws renewed and flashing repaired.
For a Tenafly building with a sound frame and worn metal, restoration is often a practical alternative to a tear-off. Restoration keeps the building closed and avoids hauling away the old roof. Ask what prep is included and what coating thickness is planned.
Related service
Metal Roof Painting Tenafly, NJ
Metal roof painting is a lighter job than coating, aimed at restoring color and rust protection rather than sealing leaks. Unlike a coating, paint does not stretch to seal seams or cover screw leaks.
If a Tenafly roof is not leaking and only looks worn, paint may be all it needs. The surface still has to be cleaned of chalk and rust primed first, or the paint will peel. If the roof has leaks, a coating is usually the better choice.
Local help
Metal Roof Coating Near Me
In Tenafly, many metal coating jobs are older exposed fastener roofs with faded paint and leaking screws. Across Tenafly and nearby communities including Cresskill, Englewood, Englewood Cliffs and Demarest, metal roofs on farm buildings and shops are frequent coating candidates, which is why an inspection before rust spreads is so useful.
Need metal roof coating around Tenafly? Call (551) 355-3330 for a Tenafly roofer who serves the towns around it too.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Tenafly is busiest after a hard winter and before the next one.
Why call
Why fix it now
Smaller repairs
Small roof problems caught early usually stay small repairs.
Roofers who know Tenafly
Local roofers see the same roofs and storm damage across Tenafly and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Metal Roof Coating questions
Silicone or acrylic: which coating is best for metal?
Acrylic and silicone are the two most common coatings for metal roofs. Acrylic recoats easily, while silicone resists standing water but limits future recoat options. The right choice depends on drainage and how you plan to maintain the roof.
What is the difference between painting and coating a metal roof?
A coating is many times thicker than paint and stretches to seal seams and fasteners. Leaky roofs need a coating, and dry roofs that only look worn can often be painted. Prep matters equally for both.
Is my metal roof a good candidate for coating?
The best candidates are structurally sound roofs with surface rust, faded paint and leaking fasteners or seams. If panels are rusted through across the roof, replacement is usually better. Call (551) 355-3330 to have the roof evaluated.
When will a coated metal roof need recoating?
The life of a coating depends mostly on its thickness and type. Thicker applications last longer, and recoating before the coating wears through renews it without starting over. Regular inspections show when a recoat is due.
Will a coating stop my metal roof from leaking?
A properly applied coating closes the common leak points on metal. Rust holes and loose panels have to be repaired first, since a coating will not span a hole or hold a loose panel down. An inspection shows whether a coating will solve your leaks.
More questions? Call (551) 355-3330
Other services that may help
Metal Roof Repair
Repairs for leaking fasteners, open seams, rusted panels and failed flashing on a metal roof, so the panels keep shedding water for years more.
Learn moreRoof Coating
Silicone, acrylic and other liquid coatings that renew aging flat, low-slope and metal roofs, after the seams and blisters are repaired.
Learn moreCommercial Roof Coating
Fluid-applied roof coatings that restore aging membranes and metal, built to a measured thickness.
Learn moreMetal Roof Inspection
A close check of the fasteners, seams, finish, trim and flashing on a metal roof, before small fastener problems become leaks.
Learn more
Looking for something else?
See all roofing servicesTalk to a Tenafly roofer about metal roof coating
Call (551) 355-3330 for a local roofer in Tenafly and nearby towns.